The team at Escale Rigging is making good progress with our sailplan modifications. Although the boat is a total construction zone right now, it’s great to see all the work getting done.
I’ve had some people ask why I have to make these changes on a brand new boat? The answer is, I don’t “have” to make any changes, but I did think it was likely that I would want to make some modifications to the headsails after I had sailed the boat for a year and that’s what this project is about. If you’ve read my earlier posts on the construction process you know that I was very happy with the advice I received from Outremer when we selected all the options we wanted to install, but there were some things that I just couldn’t decide on without spending time sailing the boat, so I asked Outremer to install the structural elements we would need for the different headsail options, and I deferred the final decisions on the sailplan until after our first year of sailing.
The ceiling lining was removed to install the genoa sheet pad-eyes and to route power and control cables and the pneumatic lines for the UpsideUp system.
The cabinets were removed to install controls for the new headsail furler winch and to convert the genoa sheet winches to electric.
Stéphane from Outremer came over from La Grande Motte to show the guys how to disassemble the head lining, and to make sure we had sufficient reinforcement for the new genoa sheet padeyes. Everything is fine because Outremer added the reinforcing when they built the roof. Thanks Stéphane!
Almost all the equipment and materials have been ordered now, and everything should be delivered in the next few weeks.
The new 45 kg Ultra anchor and flip swivel are in place and fit onto the davits with no changes, which is great!
Outremer sent their electrical engineer over to replace the faulty level gauges on the water tanks. Outremer’s R&D team has done a lot of testing with different level sensors to find a model that is accurate and reliable. This was made more complicated because the sensors need to be quiet, as the water tanks are under the beds. The sensors that use a sliding magnet ring are very reliable, but are too noisy, so we needed to find a reliable capacitive sensor that has no moving parts. The new sensors and gauges are now installed and are working well.
The halyards and reefing lines have been replaced with higher performance Dyneema/Technora lines and Escale Rigging fitted extra dyneema sleeves over the friction areas of the new lines to make them even more resistant to chafing.
The original 1st reef line uses a dyneema/polyester blend which shows significant chafe after 1 season of use where it runs through the low friction ring on the sail leech
The new reefing lines are higher load dyneema/technora and have friction reducing dyneema sleeves
You can see the anti-friction sleeve on the gennaker halyard (which we use to hold up the boarding bridge when we are at the dock). The sleeve protects from chafe where the halyard enters the mast.
New halyards
We did have one surprise when the guys were up the mast to route the new halyards, they found the outer coating has come away from around the opening where the forestay attachment loops enter the mast, exposing the carbon fiber edge, which could cause chafing of the dyneema loops.
Outremer has contacted Lorima, the mast manufacturer, and they are sending us instructions on how to fix it. It’s not a structural fault, but it is something that could chafe the forestay attachment loops over time, and it serves as a reminder of the importance of doing thorough rig checks every season, even on new boats!
Mainsail batten fitting still not fixed!
I’m still waiting for a replacement for the fitting that attaches the top batten of the mainsail to the mast. The fitting broke during the Outremer cup in May, and we have been waiting since August for Incidences (the sail manufacturer) to figure out why it broke and to send us a replacement.
Our broken fitting on the left vs the original fitting on the right. The 3 holes in a line create a weak zone which caused the fracture.
After Incidences sent me two replacements that were exactly the same as the one that broke, I pulled our broken one out of the sail and sent it to Outremer so they could work it out directly with Incidences. The response from Incidences is that the fitting broke because the attachment holes are all in a line, which creates a weak zone. They are manufacturing a replacement from a stronger material with the holes staggered. I can’t understand why this has taken 4 months to fix (so far) and we can’t use the boat without it, so I’m certainly not a fan of Incidences right now!
New headsails
Our new headsails (genoa, staysail and storm jib) are currently being manufactured by North Sails (I won’t buy sails from Incidences again after the batten fitting debacle) at the North USA factory, which is where all the new 3Di sails are made. I’m hearing really great reports from other owners about these sails having excellent durability on long distance cruising boats, so hopefully we will be happy with them also.
I’ll post an update as work progresses, and hopefully some video as well.